Hpimageassistant. Running HP Image Assistant Silently During OSD

Driver Packs (64

hpimageassistant

Now delete the files in the folder before the next test. The first being that it still goes to the net for the cab file and the knowledge base file. So, that seems to be an issue. The has been around for a little over a year. It also posts basic info to a log file on the client.

Nächster

Apply Firmware and Driver Updates Using HP Image Assistant

hpimageassistant

Unless you include the -quiet switch on the Invoke-RepositorySync command, you should see something similar to the following when running the script. You will need to confirm that each of your platforms are supported with the osver you are attempting to sync. If the repository is not fully up to date, the client will download anything newer than what is in the repository. Valid values are win7, win8, win81, win8. Also note the continue on error option is checked.

Nächster

HP PCs

hpimageassistant

Creating a Repository Detailed Repository creation and maintenance steps are documented at the blog. I am not sure if you are having issues with the repository update script or the actual task sequence steps. It kinda defeats the purpose of the beautiful scheduled script above. The repo update script is logged in a couple of different places. I'll put a better quality image of the smsts.

Nächster

The new HP Image Assistant

hpimageassistant

There is a log for each individual model sync in the. Which system s are you using in your environment? I have the download script working. This will allow for installing the management engine driver on the first pass, followed by updating management engine firmware on the second pass. Reinstall option after a successful deployment Conclusion: I believe an available deployment to end users is a great way to facilitate self service updates for firmware and drivers. The following silent command will analyze the current model, then download and install any needed firmware and driver softpaqs. I ended up putting it into the models table so that you could download different versions for older models.

Nächster

[SOLVED] Using HP Image Assistant in MDT 2013

hpimageassistant

It is possible to use this as a required deployment as well, but that could be risky in my opinion. This results in no bin file remaining. If this test was successful you can now attempt to install. When I tested it, it took the whole 90 minutes and timed out. Firstly, where can I get the product codes from? Much of the script is the same, with two main differences. Welcome to Spiceworks and its community. Ideally I would only restart if required, but not sure if this can be done via this method My scripting knowledge is fairly limited and I'm sure there are more elegant ways of doing this.

Nächster

HP Support Assistant

hpimageassistant

The output folder may be empty for several minutes before data appears. Over 200 device settings can be maintained. The package contains drivers supporting both the integrated and add-in devices in an. In the one model per folder method for clean up i just remove the folder and the line in the model table. When it finished booting there were a bunch of drivers that were out of date and had to be updated. If you decide to remove a model from your environment you can modify the repository configuration and the softpaqs that were only used by that model will be deleted as soon as you run your next repository clean up action. Invoke a repository cleanup to remove old versions 5.

Nächster

HP Image Assistant Self Service Through Software Center

hpimageassistant

InterpretedFrameInfo} InnerException : TargetSite : Void CheckActionPreference System. Note: Some hardware devices have additional software tools to help enhance the experience of using the device. Prep Work: I already had repositories for each of my models created using my PowerShell script. I ran your command and it donwloaded and started the installation for the driver that was missing. Hey Ryan, thank you for this write up. Using much of the same script from , method 3 will keep the model repositories synchronized and cleaned up, and distributed through ConfigMgr. After the Softpaq repository is available, develop a PowerShell script that will be pushed to the client and run as either a Package with a Program or a Task Sequence from the Software Center if set as Available , or run automatically if set as Required The Script The following script can be a starting point.

Nächster